- UID
- 1558
- 阅读权限
- 30
- 注册时间
- 2010-3-8
会员
- 注册时间
- 2010-3-8
|
Welcome to the Lockit Buddy website.
The Lockit Buddy is a small device that is aimed at the professional sound recordist, currently being confronted with increasing amounts of footage shot on Canon* 5DMKII/7D/T2i/550D/60D... Digital SLR cameras, and to the owners of such cameras who want to work with a professional sound recordist using double system sound linked by Timecode.
Lockit Buddy takes care of the level and impedance conversions needed to record an accurate and dependable Timecode signal and confidence audio track to the Digital SLR camera at a fraction of the cost of other available systems.
There are no brand new RF systems to be purchased, no expensive special lockit boxes that only work on your Digital SLR mini-jack connector... all you'll need is any standard Timecode source, (Lockit box, broadcast camera TC out, hard disk recorder TC out etc ...) a sound source with a professional line level or standard headphone level output (IFB receiver, mixer output etc...) and a NLE that can handle audio TC. (Avid, FCP)
All connections to and from the Lockit Buddy are made with gold plated contacts to ensure a trouble free long life with minimal signal loss.
It will accept standard SMPTE LTC via the in built BNC connector, and left and right unbalanced line level audio signal via 3-pin Mini XLR connector.
(these audio signals will be mixed down at an equal ratio by the Lockit Buddy to a single mono reference audio track on the Digital SLR).
The Lockit Buddy introduces no noise whatsoever to your signal chain and keeps crosstalk between the input channels on your Digital SLR to an absolute minimum, while making sure that no excessive levels are being sent to the camera.
Why put your reputation on the line by forcing pro line level signal (+4dB) into powered microphone level inputs? (+/- 50dB more sensitive) It may work if you turn the camera's input level all the way down in manual mode and you are willing to live with horrible crosstalk between your channels and no signal headroom, but it could cause damage to the camera inputs over time and compromise reliability of your signal.
So how does the Lockit Buddy solve these problems?
The Lockit Buddy provides a separate pre-set attenuation and impedance compensation circuit for both of it's inputs (timecode and audio), so that any equipment attached is 'seeing' the right kind of conditions to deliver it's signal into without straining it's outputs. It also cancels out the 'plug in power' being fed back from the camera microphone input to the attached equipment. The Digital SLR is getting reliably signal into it's inputs at the level it's expecting, without the crosstalk associated with sending hot signals down unbalanced connections.
There is a difference in setup between the 5DMKII / 60D model camera's which have the option to use manual gain and the rest of the range 7D/T2i etc ... which only have the auto gain option (unless you're using Magic Lantern software). Hence there are Lockit Buddies available for each system. Both versions are physically identical, but have been factory set up to attenuate signal in a different way.
(if it becomes necessary this can be modified by adjusting two internal trim controls)
In case of the auto gain cameras the Lockit Buddy uses the constant signal of the TImecode input to defeat the auto gain feature and produces an audio input free from the usual 'noise floor' artefacts. This will open up the entire dynamic range of the audio channel so a good quality reference audio track can be recorded on the camera.
In case of the 5DMKII / 60D we recommend downloading the latest firmware update for your camera and using the manual audio settings. This way a reference tone and Timecode signal can be put into allignment with one another and can be referenced to the meter display on the camera.
(This feature can be accessed via the 2nd setup menu / Live View - Movie Func. Set. / Sound Recording)
Lockit Buddy sends your reference audio track to channel 1 (L) and the Timecode to channel 2 (R).
This is conform to channel arrangements needed to ingest material with LTC recorded as audio with Avid* editing systems. For editing in Final Cut Pro* we recommend processing the video files using FCPauxTC by VideoToolshed* to extract your Timecode and turn it into an Auxiliary TC track.
In terms of mounting options, the Lockit Buddy comes standard with an aircraft grade aluminium mount that slides into the camera's flash bracket **. This mount also comes with industry standard 1/4 inch thread to allow more options mounting on rigs, spigots, etc ... or it can be taken off completely by removing two screws from the units bottom lid to allow you to use it with Velcro or an alternative way of affixing it.
Because of the multitude of possible wiring and plug arrangements connecting the Lockit Buddy to various third party devices, and due to the diversity in available rig setups, we are currently not providing any cables with the unit. Therefore we have included a
 wiring reference with some standard industry connections that you can take to your trusted audio electronics supplier to either have your cables made to order or choose from their already available range of cables to suit your specific needs. You should always make use of quality cables, keep cable lengths to a practical minimum to reduce interference and always carry spares when you're out on a shoot !
The Lockit Buddy has been intensively field tested with great reviews from users and post production companies and is now available to you with a 1 year limited warranty ***
You can find out about our WEEE return policy here. 
A user manual is now also available for download
We are now accepting Orders !
Lockit Buddy (Inclusive of 20% VAT + FREE postage) GBP 94.99
Orders will be shipped out fully insured, and on a first ordered basis.
Please note that the anticipated shipping time is presently 2-3 weeks.
If you want to pre-order please contact us with your details via[email=info@lockitbuddy.com?subject=Order%20Request&body=Please%20provide%20us%20with%20your%20details%20and%20%20your%20required%20Lockit%20Buddy%20version%20below%20!] email[/email]
* F.A.S. is not affiliated in any way with any of the companies, brand names or products mentioned. All these companies are owners of their respective registered trademarks.
** Take care when mounting on camera's that have the flash unit built in like the 7D/T2i/550D/60D as the flash unit may hit the Lockit Buddy housing when popping out.
In this case it's best to either attach an adequate strip of self adhesive rubber to the bottom of the housing to protect the flash unit or to mount the Lockit Buddy elsewhere.
No liability shall be accepted regarding damage caused as a result of ignoring this advice.
*** Your Lockit Buddy is warranted for one year from the date of purchase by F.A.S. to be free of defects in materials and workmanship. In event of such defect, product will be
repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to F.A.S., prepaid, together with the sales slip or
other proof of purchase date. Prior approval from F.A.S. is required for return. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to
use the product in accordance with instructions. This warranty is void in the event of unauthorised repair or modification. For return approval and shipping information,
contact F.A.S. via the email link on this page. Except to the extent precluded by applicable local laws F.A.S. WILL HAVE NO LIABILITY FOR ANY CONSEQUENTIAL,
INCIDENTAL, OR SPECIAL DAMAGES; ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE EXPIRES WHEN THIS EXPRESS WARRANTY EXPIRES.
This warranty gives you specific legal rights, and you may have other rights which vary depending on your territory. |
|
发表于 2011-1-26 16:44
楼主